je n'arrive pas à lire le disque ide dans ce boitier externe, voici ce que j'ai lors du montage :
SCSI error : 0 0 0 0 return code = 0x70000
end_request: I/O error, dev sda, sector 48
SCSI error : 0 0 0 0 return code = 0x70000
end_request: I/O error, dev sda, sector 56
système mandriva 2006
lsusb :
ID 05e3:0702 Genesys Logic, Inc. USB 2.0 IDE Adapter
dans un ancien sujet sur ce boitier, Grégory Auzanneau
a dit "Sinon, au niveau de la configuration du kernel, celà reste "normal", j'entend par là EHCI pour mon port usb2.0 et le Mass Storage Support avec quelques options dans la section SCSI."
quels sont ces options SCSI ?
Forum Linux.noyau Genesys Logic, Inc. USB 2.0 IDE Adapter
23
mar.
2006
# SCSI
Posté par Gregory Auzanneau (site web personnel) . Évalué à 1.
Ca fait un moment que tout se passe très bien sans (kernel d'origine debian).
Peux tu copier/coller tout ce qui concerne ton disque dur USB à partir du dmeg
[^] # Re: SCSI
Posté par boirelbr . Évalué à 1.
Linux version 2.6.12-12mdk (apatard@n1.mandriva.com) (gcc version 4.0.1 (4.0.1-5mdk for Mandriva Linux release 2006.0)) #1 Fri Sep 9 18:15:22 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bfe0000 (usable)
BIOS-e820: 000000000bfe0000 - 000000000bff0000 (reserved)
BIOS-e820: 000000000bff0000 - 000000000bff8000 (ACPI data)
BIOS-e820: 000000000bff8000 - 000000000c000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
191MB LOWMEM available.
...
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x00008000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
...
Yenta: CardBus bridge found at 0000:00:03.0 [1014:01a3]
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
Yenta: ISA IRQ mask 0x02b8, PCI irq 10
Socket status: 30000821
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
ohci_hcd 0000:01:00.0: OHCI Host Controller
ohci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:01:00.0: irq 10, io mem 0x0c800000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Enabling device 0000:01:00.1 (0000 -> 0002)
ohci_hcd 0000:01:00.1: OHCI Host Controller
ohci_hcd 0000:01:00.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:01:00.1: irq 10, io mem 0x0c801000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Enabling device 0000:01:00.2 (0000 -> 0002)
ohci_hcd 0000:01:00.2: OHCI Host Controller
ohci_hcd 0000:01:00.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:01:00.2: irq 10, io mem 0x0c802000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-2: new full speed USB device using ohci_hcd and address 2
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
PCI: Enabling device 0000:01:00.4 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.4 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[c803000-c8037ff] Max Packet=[2048]
PCI: Enabling device 0000:01:00.3 (0000 -> 0002)
ehci_hcd 0000:01:00.3: EHCI Host Controller
ehci_hcd 0000:01:00.3: debug port 1
ehci_hcd 0000:01:00.3: new USB bus registered, assigned bus number 5
ehci_hcd 0000:01:00.3: irq 10, io mem 0x0c803800
ehci_hcd 0000:01:00.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 6 ports detected
usb 5-2: new high speed USB device using ehci_hcd and address 2
usb 2-2: USB disconnect, address 2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0090e6390000018d]
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x2c8-0x2cf 0x3b8-0x3df 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
eth1394: $Rev: 1247 $ Ben Collins <bcollins@debian.org>
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Floppy drive(s): fd0 is 1.44M
Vendor: ST312002 Model: 2A Rev: 0811
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: assuming drive cache: write through
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: assuming drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1 p2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Intel 810 + AC97 Audio, version 1.01, 18:11:20 Sep 9 2005
PCI: Found IRQ 11 for device 0000:00:00.1
PCI: Sharing IRQ 11 with 0000:00:00.2
IRQ routing conflict for 0000:00:03.0, have irq 10, want irq 11
PCI: Setting latency timer of device 0000:00:00.1 to 64
...
usb 5-2: reset high speed USB device using ehci_hcd and address 2
scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0
SCSI error : <0 0 0 0> return code = 0x50000
end_request: I/O error, dev sda, sector 124937505
Buffer I/O error on device sda2, logical block 0
scsi0 (0:0): rejecting I/O to offline device
Buffer I/O error on device sda2, logical block 0
scsi0 (0:0): rejecting I/O to offline device
Buffer I/O error on device sda2, logical block 64
scsi0 (0:0): rejecting I/O to offline device
Buffer I/O error on device sda2, logical block 64
... je débranche mon cable usb puis rebranche sur le 2ème port usb
usb 5-2: USB disconnect, address 2
usb 5-1: new high speed USB device using ehci_hcd and address 3
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
Vendor: ST312002 Model: 2A Rev: 0811
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: assuming drive cache: write through
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: assuming drive cache: write through
/dev/scsi/host1/bus0/target0/lun0: p1 p2
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
usb-storage: device scan complete
SCSI error : <1 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 360
Buffer I/O error on device sda1, logical block 297
SCSI error : <1 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 361
Buffer I/O error on device sda1, logical block 298
SCSI error : <1 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 362
Buffer I/O error on device sda1, logical block 299
SCSI error : <1 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 363
Buffer I/O error on device sda1, logical block 300
SCSI error : <1 0 0 0> return code = 0x70000
end_request: I/O error, dev sda, sector 364
Suivre le flux des commentaires
Note : les commentaires appartiennent à celles et ceux qui les ont postés. Nous n’en sommes pas responsables.