Bonjour à tous.
Je viens d'installer la distribution Linux Mandriva LE 2005.
L'installation s'est bien passée, mais Linux ne démarre pas:
Je m'explique:
J'allume l'ordinateur, là j'obtiens l'interface graphique de Lilo.
Je lui demande de booter sous Linux. C'est là que ça se gâte:
j'obtient la jolie tête du pingouin Mandriva, et la barre de progression
n'avance pas.
Idem en choisissant FailSafe.
Je relance alors le DVD et j'entre lors l'invite boot : rescue.
Là j'arrive à lancer un shell, à monter une bonne vielle disquette
3p1/4 et taper la un dmesg avec une redirection vers /mnt/floppy.
(au fait existe-il un moyen d'ecrire sur un systeme de fichier NT à
partir de Linux ?)
Voici le resultat de dmesg. Pardonnez moi car il est un peu long !
Pouvez-vous m'aider pour que Linux boot enfin ? Comment
décrypter la sortie de dmesg ?
Merci d'avance de votre aide.
A bientôt
Chris.
Linux version 2.6.11-6mdk-i586-up-1GB (gb@n2.mandrakesoft.com) (gcc version 3.4.3 (Mandrakelinux 10.2 3.4.3-3mdk)) #1 Tue
Mar 22 15:46:07 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d8000 - 00000000000e0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fef0000 (usable)
BIOS-e820: 000000000fef0000 - 000000000feff000 (ACPI data)
BIOS-e820: 000000000feff000 - 000000000ff00000 (ACPI NVS)
BIOS-e820: 000000000ff00000 - 000000000ff80000 (usable)
BIOS-e820: 000000000ff80000 - 0000000010000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65408
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61312 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f82e0
ACPI: RSDT (v001 PTLTD RSDT 0x06040001 LTP 0x00000000) @ 0x0fefc11b
ACPI: FADT (v001 FSC D1675 0x06040001 0x000f4240) @ 0x0fefc14b
ACPI: MADT (v001 FSC APIC 0x06040001 CSF 0x00000000) @ 0x0fefef92
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040001 LTP 0x00000001) @ 0x0fefefd8
ACPI: DSDT (v001 FSC D1675 0x06040001 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0xf008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
Allocating PCI resources starting at 10000000 (gap: 10000000:eec00000)
Built 1 zonelists
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
Kernel command line: initrd=alt0/all.rdz ramdisk_size=128000 automatic=method:cdrom acpi=ht rescue BOOT_IMAGE=alt0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 2523.389 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 250904k/261632k available (2074k kernel code, 9964k reserved, 687k data, 240k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4997.12 BogoMIPS (lpj=2498560)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
CPU: Intel(R) Pentium(R) 4 CPU 2.50GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4101k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd99d, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Disabled
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Uncovering SIS963 that hid as a SIS503 (compatible=1)
Enabling SiS 96x SMBus.
PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
PCI: Using IRQ router SIS [1039/0963] at 0000:00:02.0
PCI: IRQ 0 for device 0000:00:02.1 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Found IRQ 11 for device 0000:00:02.1
PCI: Sharing IRQ 11 with 0000:00:02.3
PCI: IRQ 0 for device 0000:00:02.5 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Found IRQ 9 for device 0000:00:02.5
Simple Boot Flag at 0x69 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1121198695.817:0): initialized
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
PCI: Found IRQ 9 for device 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0x2000-0x2007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2008-0x200f, BIOS settings: hdc:DMA, hdd:DMA
C'est à ce niveau qu'il bloque quand je boote avec Lilo.
Probing IDE interface ide0...
hda: WDC WD1200LB-55EDA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ATAPI DVDROM 16X, ATAPI CD/DVD-ROM drive
hdd: _NEC DVD+RW ND-1100A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 >
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
PCI: Found IRQ 11 for device 0000:00:02.3
PCI: Sharing IRQ 11 with 0000:00:02.1
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[e4010000-e40107ff] Max Packet=[2048]
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Found IRQ 9 for device 0000:00:03.0
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: irq 9, pci mem 0xe4011000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:03.1
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: irq 11, pci mem 0xe4012000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:03.2
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: irq 10, pci mem 0xe4013000
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Found IRQ 9 for device 0000:00:03.3
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: irq 9, pci mem 0xe4014000
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 2-1: new full speed USB device using ohci_hcd and address 2
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0030053100097c20]
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
hdc: ATAPI 32X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
loop: loaded (max 256 devices)
gzloop: loaded
/sysroot/tmp/rescue.clp: 496 blocks, 65536 bytes/block, largest block is 65562 bytes.
ISO 9660 Extensions: RRIP_1991A
Freeing unused kernel memory: 240k freed
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET: Registered protocol family 17
SGI XFS with ACLs, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
SCSI subsystem initialized
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected SiS 648 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xe0000000
i2c-sis96x version 1.0.0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x8100
PCI: Found IRQ 5 for device 0000:00:02.7
PCI: Sharing IRQ 5 with 0000:00:14.0
codec_ready: codec is not ready [0x340000]
Intel ICH: probe of 0000:00:02.7 failed with error -5
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Found IRQ 11 for device 0000:00:06.0
tulip0: MII transceiver #1 config 3100 status 7849 advertising 01e1.
eth0: ADMtek Comet rev 17 at 00011800, 00:30:05:59:46:EB, IRQ 11.
VFS: Can't find ext3 filesystem on dev hda.
VFS: Can't find an ext2 filesystem on dev hda.
ReiserFS: hda: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hda
XFS: bad magic number
XFS: SB validate failed
VFS: Can't find ext3 filesystem on dev hda1.
VFS: Can't find an ext2 filesystem on dev hda1.
ReiserFS: hda1: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hda1
XFS: bad magic number
XFS: SB validate failed
attempt to access beyond end of device
hda2: rw=0, want=4, limit=2
EXT3-fs: unable to read superblock
attempt to access beyond end of device
hda2: rw=0, want=4, limit=2
EXT2-fs: unable to read superblock
attempt to access beyond end of device
hda2: rw=0, want=18, limit=2
ReiserFS: hda2: warning: sh-2006: read_super_block: bread failed (dev hda2, block 8, size 1024)
attempt to access beyond end of device
hda2: rw=0, want=130, limit=2
ReiserFS: hda2: warning: sh-2006: read_super_block: bread failed (dev hda2, block 64, size 1024)
ReiserFS: hda2: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hda2
attempt to access beyond end of device
hda2: rw=0, want=8, limit=2
XFS: SB read failed
attempt to access beyond end of device
hda2: rw=0, want=72, limit=2
attempt to access beyond end of device
hda2: rw=0, want=128, limit=2
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Forum Linux.mandriva Mandriva LE2005 : problème de boot
23
juil.
2005
Suivre le flux des commentaires
Note : les commentaires appartiennent à celles et ceux qui les ont postés. Nous n’en sommes pas responsables.